![]() ![]() On this page only the VX-9000 model is indicated as compatible. In addition, I have not found any online publications that show that the VX-2100 was used with MMDVM. This will only be confirmed with an MMDVM assembly and adjustment. Usually it is found that the equipment can transmit at 9600 bauds, if this is the case, this leads to the conclusion that the station could be compatible. I read the service Manual of VX-2100 (Here is a link from ). Les signaux de sortie de ligne audio peuvent être obtenus à partir de ce connecteur pour une utilisation avec des accessoires tels que les modems de transmission/réception de données, l’entrée de contrôle de canal externe, etc. La radio est équipée d’un connecteur d’accessoires Sub-D à 15 broches.Įntrée ligne audio TX externe, PTT (Push To Talk), Squelch et réception RX Pouvez-vous s’il vous plaît jeter un coup d’oeil aux spécifications et donner votre opinion pour connecter les radios en DMR ? J’avais l’intention de connecter les 2 radios au mode DMR du MMDVM. J’ai deux radios de la série Vertex VX-2100. The radio have a D-Sub 15-Pin Accessory ConnectorĮxternal TX audio line input, PTT (Push To Talk), Squelch, and external RXĪudio line output signals may be obtained from this connector for use with accessories such as data transmission/reception modems, and external Channel control input etc. Can you please have a look at the spec and give your opinion to connect the radios to DMR? I was planning to connect the 2 radios to the MMDVM DMR Mode. Est-ce que la combinaison de touches de programmation du Tait doit être réalisé pour pouvoir réaliser la programmation?Įt quelle version du logiciel avez-vous utilisée, et pourriez-vous l’envoyer pour un test? De plus, quel câble avez-vous utilisé, homebrew ou câble standard? Mais maintenant, j’ai des difficultés avec la programmation. Mais après avoir testé avec mes vieilles radios mobiles, j’ai fini par les changer avec quelque chose de testé. Je construis un relais DMR en utilisant votre platine mmdvm à base de nucleo. Is the Tait have programming key combination to be changed for programming?Īnd what version of the software did you use, and could you send it for a test? Also what cabe did you use, homebrew or stock cable? But now I have strugles with programming and do further testing. But after testing with my old mobile radios I ended up changing them with something tested. I am building dmr using your mmdvm shield based on nucleo. C’est justement une des fonctions apportés par ma platine adaptateur de prise accessoire Motorola. C’est par contre nécessaire pour les motorola. De mon côté, je n’ai pas eu besoin de limiter le niveau audio transmit par le TM8110, donc pas de diviseur de tension. Par ailleurs, je ne pense pas qu’il soit intéressant de démonter le potentiomètre de réglage de l’émission puisque le régler en buté est suffisant. J’ai noté aucune évolution de qualité en fonction de la largeur de bande de réception (12.5 ou 20 kHz). This is precisely one of the functions provided by my Motorola accessory plug adapter. It is yes necessary for the motorola transceivers. On my side, i had no need to limit the audio level transmiting by the TM8110, so no voltage divider here. Otherwise, i think there is no interest to disassemble the TX pot because tuning it to stop position is enough. I have not note any evolution of quality in function of bandwith reception (12.5 or 20 kHz). Do not hesitate to share your experiences by submitting your comments at the bottom of the page. This configuration may well be suitable for other series of the TAIT ® brand. ![]() Here is your MMDVM repeater ready to operate with TAIT ® transceivers of the TM8100 series. ![]() We start MMDVMHost … sudo /opt/MMDVMHost/MMDVMHost /opt/MMDVMHost/MMDVM.ini
0 Comments
Leave a Reply. |